HCH II-Specific Discussions Model Years 2006-2011

Firewall access for 12 batt access?

Thread Tools
 
Search this Thread
 
  #1  
Old 04-16-2008, 06:30 PM
holicow's Avatar
Active Enthusiast
Thread Starter
Join Date: Jun 2004
Location: Turtle Jxn, NC
Posts: 139
Default Firewall access for 12 batt access?

I would like to install my compact amp/subwoofer (Kenwood WOOX) in my new HCH II. I need to get access through the firewall to the 12v battery for a power source. I do not see an obvious (or easy) access, and would prefer not to cut into the harnesses that do pass through.

Any suggestions, or has anyone done this already?
 
  #2  
Old 04-16-2008, 07:26 PM
msantos's Avatar
Eco Accelerometrist
Join Date: Jun 2006
Location: Winnipeg, MB
Posts: 1,191
Default Re: Firewall access for 12 batt access?

I suggest you use the live 12V rail on the fuse panel.

You should have quite a few empty fuse sockets that will give you power without the need to snake through the firewall. Just make sure you amp is fused so as to keep things safe.

Cheers;

MSantos
 
  #3  
Old 04-16-2008, 08:23 PM
Orient Express's Avatar
Über Lord of Hypermillia
Join Date: Aug 2006
Location: San Francisco Bay Area
Posts: 652
Default Re: Firewall access for 12 batt access?

Second that. There are 3-4 switched and unswitched fuse positions available in the interior fuse block. All will handle 20 amps fine.
 
  #4  
Old 04-17-2008, 10:02 AM
holicow's Avatar
Active Enthusiast
Thread Starter
Join Date: Jun 2004
Location: Turtle Jxn, NC
Posts: 139
Default Re: Firewall access for 12 batt access?

Thanks, great idea. I have put in an in-line fuse, so that should be covered.
 
  #5  
Old 04-17-2008, 10:23 AM
Kennedy's Avatar
Enthusiast
Join Date: Mar 2008
Posts: 46
Default Re: Firewall access for 12 batt access?

Originally Posted by Orient Express
Second that. There are 3-4 switched and unswitched fuse positions available in the interior fuse block. All will handle 20 amps fine.
If you're using the stock fuse block, do you need to order the proper termination connector to use the stock fuse?
 
  #6  
Old 04-18-2008, 08:02 AM
Orient Express's Avatar
Über Lord of Hypermillia
Join Date: Aug 2006
Location: San Francisco Bay Area
Posts: 652
Default Re: Firewall access for 12 batt access?

Originally Posted by Kennedy
If you're using the stock fuse block, do you need to order the proper termination connector to use the stock fuse?
The "Add a Circuit" fuse taps actually have a slot in them for the existing fuse, and a second position for a fuse to service the new circuit. In the photo, you can see that I have added 3 additional fused circuits to the car.

 
  #7  
Old 04-18-2008, 01:40 PM
giantquesadilla's Avatar
Ridiculously Active Enthusiast
Join Date: Jul 2007
Location: San Diego, CA, USA
Posts: 941
Default Re: Firewall access for 12 batt access?

OE: I have two questions.
1. Where do you get those add-a-fuse things? I just have a wire going into the fuse box and an inline fuse later on.
3. What are all of those fuse taps for. (I'm trying to think of the mods you've done... maybe one is for the backup sensors?)
 
  #8  
Old 04-18-2008, 02:17 PM
Orient Express's Avatar
Über Lord of Hypermillia
Join Date: Aug 2006
Location: San Francisco Bay Area
Posts: 652
Default Add a Circuit

The Add a Circuit inline fuseholders are available at most auto parts stores.

The circuits that I have added to my HCHII are:

1. An ambient LED light to illuminate the center console. This is connected to the low-beam lighting circuit so it comes on only when the headlights are on.



2. An unswitched circuit for the illuminated door scuff plates



3. A switched circuit for the backup sensors

 
  #9  
Old 04-19-2008, 08:30 AM
giantquesadilla's Avatar
Ridiculously Active Enthusiast
Join Date: Jul 2007
Location: San Diego, CA, USA
Posts: 941
Default Re: Firewall access for 12 batt access?

Thanks.
 
  #10  
Old 04-20-2008, 05:59 AM
holicow's Avatar
Active Enthusiast
Thread Starter
Join Date: Jun 2004
Location: Turtle Jxn, NC
Posts: 139
Default Re: Firewall access for 12 batt access?

Originally Posted by Orient Express
The "Add a Circuit" fuse taps actually have a slot in them for the existing fuse, and a second position for a fuse to service the new circuit. In the photo, you can see that I have added 3 additional fused circuits to the car.

Can you point out which of the open spots are ignition-switched? I don't have my shop-manual (yet) and would like to use an empty one rather than piggy-back on a currently used circuit.

Thanks for the help so far!
 


Quick Reply: Firewall access for 12 batt access?


Contact Us -

  • Manage Preferences
  • Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Your Privacy Choices -

    When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

    © 2024 MH Sub I, LLC dba Internet Brands


    All times are GMT -7. The time now is 06:18 AM.