Anyone have the pdf's/instructions for Nav unit install

Thread Tools
 
Search this Thread
 
  #11  
Old 06-19-2020, 10:40 AM
comtec's Avatar
Enthusiast
Join Date: Jun 2020
Posts: 2
Default Re: Anyone have the pdf's/instructions for Nav unit install

Hey, Im also looking for some help on this same project. I have a 2008 Camry Hybrid with JBL (Radio A51862), purchased an OEM Nav unit from a 2007 Camry Hybrid with JBL (Radio E7011). The harness and plugs are obviously a little different on the Nav cars (attachment below), original Non-nav unit has 4 connectors F8,F11,F26 and (E18, mine was empty). 2 of the connectors/plugs: F26 & F8 are the same on on all JBL units (nav or non-nav). I wasn't even sure what to expect with just the 2 plugs connected, what would work, what wouldn't. But everything Display/Touch and radio-wise is working fine and the steering controls all work. I wanted to get some help with getting the Consumption/Energy, Aux and Nav working. Mainly wanted to get the Consumption working, but if the Aux & Nav are in the same realm of difficulty I would do that too. I'm happy with the update even as is, but wouldn't mind getting those other couple things working, I have all the nav connectors cut from the donor car harness.

From what I understand, Dan Gold is the original pioneer of this project and put together some documents and info for this retrofit.
There is some mentions of the "2007_Camry_Nav.pdf", instructions for changing from a radio to the Nav system, and "Camry34.pdf" a wiring diagram for the Nav (and radio) units.

Consumption/Energy Dang wrote:
It only requires 3 more wires compared to the non-hybrid Nav system, 2 CAN buss wires, and an ignition sense wire.
The CAN wires are located right behind the Nav, and the ignition sense wire is behind the trim on the left where the mirror controls are.

Anyone know what those exact connections are? or have any other instructions for this retrofit they can send in PM or email? any help is greatly appropriate, email is Balistocar@gmail.com. Thank you

 
  #12  
Old 02-06-2021, 06:47 AM
Mohsen Sumbal's Avatar
Enthusiast
Join Date: Jun 2020
Posts: 10
Default Re: Anyone have the pdf's/instructions for Nav unit install

Originally Posted by mitrals
Here is what I dug up:

Attached is a whack of info I’ve sent a few people!

Note there are some references here to connecting up the CAN and ignition sense for the energy screens. This is for the Hybrid unit, and you don’t need them for the non-hybrid unit.
Note that for the CAN wires, one guy just tap’d into the wires beside the blue connector I list. He says it was easier than finding pins.

Also note there are a couple of parts they talk about that appear to only be listed for Canada.

Here’s the Canadian part numbers:
C0069-33010-W2 AUX & STEERING
C0069-33010-W3 MIC CONNECTOR

Here’s what another user in the U.S. did:
Since I couldn't find the SW/Aux adapter, what I really needed was the mic connector (F12) which is P/N 90980-12404, the Aux connector (F14) P/N 90980-12209, and the (F13) connector P/N 90980-11909 if you want to add the SPD, REV, and IGN wires to the unit.

If you are going from a radio to a nav (vs. From nav to hybrid nav), before you do anything. Have a look at 2007_Camry_Nav.pdf.

I’m not sure if you have the info to get your existing radio out. It’s pretty easy. This is in 042000.pdf attached, so that 2007_Camry_Nav document covers it.
·Pry out the vent at the top and disconnect the wire.
·Unscrew your shift **** and remove it
·Pull off the two trim pieces on either side of the lower box by just pulling towards the rear.
·Lift up the plate for the shifter, it and the part right in front of the box all just pull up, from the rear.
·The entire plastic piece where the shifter is then lifts up and comes off. Disconnect the wire for the 12 volt plug.
·That will reveal two screws. Undo these and the box will come out. (Hint, have to put the car in drive to get it past the shifter bar.) There are two connections you have to disconnect on the back of the box.
·You’ll now see four screws, two above the radio/Nav, and two below the climate control. Undo these and the radio and climate control come out as one big piece. There is one connection on the back of the climate control, and a bunch on the back of the radio. Only the two antenna connections on the radio just pull. All others have a release tab.

Again the correct numbers for the Nav say E7011 on the front, and part number 86120-33A30 as a part number you can order from Toyota for the unit. I “think” 86120-06460 is OK as well for the hybrid, but do not have firsthand experience with this unit. Note the unit doesn’t come with a Nav disk. You have to order that seperate.

First thing for you is Camry34.pdf. This is the wiring diagram for the Nav (and radio) units.
For the version with the energy screens, there are three extra wires to be concerned with.
You will notice on the first page of the wiring diagram a connection that says IG, and says 10A ECU IG No. 1. This is only for Nav units. This goes to pin 2 of the 5 pin connector on the back of the Nav. Pin 3 is the speed wire, and pin 5 is the reverse wire on all Nav systems, but pin 2 is connected only on hybrid cars.
You need to run a wire from pin 10 of 3L. Don’t try to go to pin 2 of 3Q. You have to take your entire dash out, and it’s just not worth it.
I took the lower part of the dash out (under the steering wheel), but I “think” you should be able to just pull the trim piece to the left of the steering wheel where the power mirror controls are.
If you look at 088.jpg, you will see a picture. You can see the black on the second connector down. You’ll notice I stripped back the insulation on this, and added my wire to run to pin 2 of the 5 pin on the back of the Nav there. 0084.jpg is a closer look at this. I of course soldiered and taped this after I took the picture.
The other two wires you will need are the CAN buss wires. Back to the wiring diagram in camry34.pdf, go to page 5. You will notice CANH can CANL on pins 2 and 3 of F12. These connect up to FE2, right behind the Nav. Pin 2 goes to pin 18, and pin 3 to pin 19. Picture 076.jpg is a close-up of F12, and you can see the two yellow wires I added. If you look at the same picture, you’ll notice a blue connector sort of below/behind the black plastic part. That’s FE2, where you want to connect those CAN wires. (they were not connected yet when I took the shot.)
You will need a least five .5mm pins. I would try to get these from Toyota. I actually cheated and used some VW/Audi ones I had, but they were a bit of a challenge to get in. Toyota ones from the dealer would be better.

Two more attachments I thought would be handy for you.
035003.pdf tells you what all the connections do on the back of the radio.
036006.pdf is the connections for the Nav, and also some diagnostic menus.
036004.pdf is more diagnostics for the Nav. Note on page 11 it talks about a CAN check. Only models with the energy screens have this diagnostic screen.
One caution. There is one unused terminal on the Nav and oddly the climate control connection will fit in there. Don’t make that mistake.

Finally, 2007_Camry_Nav.pdf is the instructions for changing from a radio to the Nav system. These are the dealer instructions. Again, the instructions do not cover the three additional wires required for the energy screens above, but otherwise are what you need.

I “highly” recommend you get the install kit from the dealer. The connectors are different between the radio and the Nav, and this kit comes with a great adapter to make it work. You can see a picture of the adapter on page 7. They also provide some other connectors. The part number for this kit is on the first page.

Some handy numbers:
PU069-32777-G5 NAV SYS GEN 5
C0069-33010-W2 AUX & STEERING
C0069-33010-W3 MIC CONNECTOR

I think that’s it. Please don’t hesitate to contact me if you have any questions or problems.

Thanks!

Dan


Current student attempting to make my 07 Camry pretty again for some trips/outings. Need small help. I’ve acquired all the harnesses and parts to finish my oem retrofit for my 2007 camry Hybrid GPS NAV system. Its at my mechanics right know and we’ve hit a small roadbblock involving the wiring on the new 5 pin Harness that must be installed/spliced. We have the original instruction pdf files for installing the system but the PDF file does not say where the wiring placement for the AE5-blue speed signal, and the AE6-Yellow reverse signal attache/what pin/color wire to splice them into. I can/will attach some pictures to help show what were dealing with. If theirs any extra wiring information that you think may be useful to me could you forward that as well. My email is mohsen.sumbal303@gmail.com All information and documents would be god sent. Thanks everyone have a great year!






 
Related Topics
Thread
Topic Starter
Forum
Replies
Last Post
LEAKYTCH
Toyota Camry Hybrid
36
07-20-2007 11:07 AM
mistyalcove
Honda Civic Hybrid
18
01-09-2006 07:00 AM
tigerhonaker
Honda Civic Hybrid
24
09-15-2005 06:00 PM



Quick Reply: Anyone have the pdf's/instructions for Nav unit install


Contact Us -

  • Manage Preferences
  • Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Your Privacy Choices -

    When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

    © 2024 MH Sub I, LLC dba Internet Brands


    All times are GMT -7. The time now is 01:35 PM.